Quick answer: To bleed a Powerstroke fuel system, turn the ignition on for 30 seconds, then off. Repeat this six times in a row before you crank. Then crank for no more than 10 seconds. Ford gives this purge procedure after a fuel filter change and after running out of fuel. Any air that is left purges itself once the engine runs.
How Do You Bleed Air From a Powerstroke Fuel System?
If you want to know how to bleed a Powerstroke fuel system, the short version is this: on trucks with an electric lift pump, you prime by cycling the ignition. Each time the key is on, the pump runs and pushes fuel through the filters and lines. That fuel pushes the trapped air out ahead of it.
Ford’s diesel owner content calls for six ignition cycles of 30 seconds on, then off. You do this before you try to start the engine. Forum threads give many different cycle counts. Start with Ford’s number.
Some air may still be in the system after the purge. Ford says that air self-purges once the engine starts. A short spell of rough idle or white smoke is normal while that happens.
Quick steps: key-cycle priming
- Make sure the filter drain is closed and the filter housing is tight.
- Turn the ignition on, but do not crank. Wait 30 seconds.
- Turn the ignition off.
- Repeat on-for-30-seconds, then off, until you have done six cycles in a row.
- Crank the engine for no more than 10 seconds.
- If it doesn’t start, turn the ignition off and wait 30 seconds before you crank again.
Why Does Air Get Into a Diesel Fuel System?
Air gets in any time the fuel system is opened or runs dry. The most common causes are:
- Changing the fuel filters.
- Running the tank dry.
- Replacing the lift pump or fuel lines.
- A loose filter bowl, a loose cap, or a water drain left open.
Ford warns that running out of fuel lets air into the fuel system, and this can make the engine hard to restart. A diesel has no spark. It needs a steady supply of fuel under pressure to fire. Air in the lines breaks up that supply. The usual result is an engine that cranks but won’t fire, or one that starts and then stalls.
This article covers air purging only. If your truck loses power or stalls without any recent filter work or a dry tank, the cause may be fuel starvation or low pressure. See our fuel starvation guides for that diagnosis.
Step-by-Step: How to Prime a Powerstroke After a Fuel Filter Change
Yes, you do need to bleed a Powerstroke after changing the fuel filters. In the 2020 Super Duty 6.7L diesel manual, the filter replacement steps end with six ignition cycles to purge trapped air.
- Park on level ground and turn the engine off. The fuel system may be under pressure, so open fittings slowly.
- Place a drain pan under the filter. On the 2020 6.7L, the fuel conditioner module filter drains about 0.53 gal (2 L).
- Drain and remove the old filter, following your manual’s steps for your model year.
- Install the new filter and any new seals that come with it.
- Close the drain until it is snug.
- Tighten the bowl or housing to its stop. Do not go past the torque limit in your manual.
- Turn the ignition on for 30 seconds, then off. Do this six times in a row.
- Crank for no more than 10 seconds. If it doesn’t start, key off, wait 30 seconds, and try again.
- Once it runs, check the housing and drain for leaks.
Some Ford owner material notes that the system purges the air in the filters on its own. Yet the same filter-change procedure still lists the six ignition cycles. Do the cycles anyway. They take about six minutes and lower the odds of a no-start or a hard crank on the starter.
Disposal: Ford says not to put drained fuel in household trash or the public sewer system. Take it to an authorized waste disposal facility. Many auto parts stores and local recycling centers can tell you where to go.
What Tools and Supplies Do You Need?
- The correct replacement filters for your engine and model year.
- A drain pan that holds more than 2 L, plus a sealable container for the old fuel.
- The right socket or filter cap tool for your housing.
- A torque wrench that reads low values in lb-ft or in-lb.
- Nitrile gloves, eye protection and shop rags.
- Your owner’s manual or diesel supplement.
How Tight Should the Filter Housing Be?
On the 2020 Super Duty 6.7L, Ford gives a maximum torque of 7 lb-ft (9 Nm) for the fuel conditioner module housing. That is light. Overtightening can damage the housing or seal.
Too loose is also a problem. Ford’s 6.7L diesel supplement says the drain should be snug and the bowl tightened to its stop. A loose bowl or drain can let air in and cause a no-start or rough idle. Check the torque spec for your own model year, because it can change.
How to Restart a Powerstroke After Running Out of Fuel
To prime a 6.7 Powerstroke after running out of fuel, add 4 to 5 gallons (15 to 19 L) of diesel. Then do six ignition cycles of 30 seconds each before you crank. Ford says that amount of fuel is normally enough to restart. You may need more if the truck is parked on a steep grade, because the fuel may not reach the pickup.
- Add 4 to 5 gallons (15 to 19 L) of clean diesel. Add more on a steep grade.
- Turn the ignition on for 30 seconds, then off. Repeat six times in a row.
- Crank for no more than 10 seconds.
- If it doesn’t start, turn the ignition off and wait 30 seconds before cranking again.
A dry tank often takes more patience than a filter change. The air may fill the lines from the tank all the way forward, not just the filter housings. If the first round fails, a second full six-cycle purge before more cranking is reasonable. Don’t make up for it with long cranking.
How Long Should You Crank a Diesel When Priming?
No more than 10 seconds at a time. Ford warns that longer cranking can damage the starter. Between attempts, turn the ignition off and wait 30 seconds. The key-on cycles do the priming. Cranking is only for starting.
Does the Bleeding Procedure Differ on the 7.3, 6.0, 6.4 and 6.7?
Yes, it can. Filter layout and the fuel supply design differ between Powerstroke generations. The verified Ford procedure in this article comes from 6.7L owner material. For other engines, use your owner’s manual or diesel supplement.
| Engine | Model years (approx.) | Filter location | Basic prime method |
|---|---|---|---|
| 7.3L Powerstroke | 1994.5–2003 | Check your owner’s manual | Check your owner’s manual. Fuel supply design changed during this engine’s run. |
| 6.0L Powerstroke | 2003–2007 | Check your owner’s manual | Check your owner’s manual |
| 6.4L Powerstroke | 2008–2010 | Check your owner’s manual | Check your owner’s manual |
| 6.7L Powerstroke | 2011–present | Engine-mounted filter plus a fuel conditioner module filter (per 2020 Super Duty manual) | Six ignition cycles, 30 seconds on, then off, before cranking |
For 7.3 Powerstroke priming in particular, don’t assume the 6.7 steps carry over. Look up the procedure for your exact year. The same goes for valve locations and fuel pressure numbers. Only use them if they come from a Ford or OEM source for your truck.
What If the Truck Still Won’t Start After Bleeding?
The most common reason a Powerstroke won’t start after a fuel filter change is air leaking in at the filter. Ford’s 6.7L supplement says an air leak at the filter bowl seal or drain can cause a no-start or rough idle after filter service. Work through these steps in order:
- Repeat the purge once. Do another full set of six 30-second ignition cycles, then crank for no more than 10 seconds.
- Check the filter. Confirm the drain is snug, the bowl or housing is at its stop, and the seal is seated and not pinched or doubled.
- Listen for the lift pump. With the key on, you should hear the pump run. If you hear nothing, the pump or its power supply needs checking.
- Stop cranking. If it still won’t start, stop. Repeated cranking can damage the starter and won’t fix a leak or a failed pump.
If you suspect a weak lift pump or low fuel pressure, that is a separate diagnosis. See our guides on low fuel pressure symptoms and how to test Powerstroke fuel pressure before you buy parts.
Is Rough Running or White Smoke Normal After Priming?
Yes, for a short time. Ford says the engine may run rough or make white smoke while air is still in the system. This is normal and stops after a short period as the remaining air purges.
Ford also says to have the vehicle checked if rough running continues. Get it checked soon if you see any of these:
- Rough running or smoke that doesn’t clear up.
- The engine keeps stalling.
- The check engine light comes on.
- Fuel is leaking at the filter housing or drain.
Mistakes to Avoid When Bleeding a Powerstroke
- Long cranking to “pull fuel” through. Ford limits cranking to 10 seconds because longer runs can damage the starter. Cranking does not replace key-cycling.
- Leaving the drain open or the cap loose. Either one can let air back in and cause a no-start or rough idle.
- Overtightening the housing. On the 2020 6.7L, the limit is 7 lb-ft (9 Nm). Check your year’s spec.
- Running the tank very low. Ford says to avoid running out of fuel. The Super Duty owner’s manual warns it may have an adverse effect on engine components.
- Pouring fuel into a new filter. Unless your manual says pre-filling is OK for your engine, don’t. Unfiltered fuel on the clean side of a filter can carry dirt toward the injection system.
- Skipping the purge. Even if your truck might start without it, the six cycles cost a few minutes and protect the starter.
Frequently Asked Questions
How many times do you cycle the key to prime a Powerstroke?
Cycle the key six times in a row before you crank. Turn the ignition on for 30 seconds without cranking, then turn it off. That is one cycle. Ford’s 6.7L diesel owner content gives this count. Forum threads list other numbers, so start with Ford’s six cycles.
Do you need to bleed a Powerstroke after changing the fuel filters?
Yes. The 2020 Super Duty 6.7L manual ends the filter replacement steps with six ignition cycles of 30 seconds on, then off. Some Ford material says the system purges air on its own. The cycles still take only about six minutes and lower the odds of a no-start or hard cranking.
How much fuel do I need to add to restart a diesel that ran out of fuel?
Add 4 to 5 gallons (15 to 19 L) of clean diesel. Ford says this is normally enough to restart a Powerstroke that ran dry. Add more if the truck sits on a steep grade, because the fuel may not reach the pickup. Then do six 30-second key cycles before cranking.
Should you pre-fill a new Powerstroke fuel filter with diesel?
No, unless your manual says pre-filling is OK for your engine. Pouring unfiltered fuel into a new filter can put dirt on the clean side. That dirt can travel toward the injection system. Use the key-cycle purge instead to fill the filters and push the air out.
