Quick answer: The most common 6.7 Powerstroke fuel pump failure symptoms are hard starts or long cranking, crank-no-start, power loss under load, sputtering, rough idle or stalling, a check engine light with code P0087 (low rail pressure), and metal flakes in the fuel filter. Metal in the filter points to the CP4.2 high-pressure pump. Stop driving if you see it.
What Are the Symptoms of a Bad Fuel Pump on a 6.7 Powerstroke?
These are the warning signs to watch for:
- Hard start or long cranking: the engine turns over longer than normal before it fires.
- Crank-no-start: the engine cranks but never starts.
- Power loss under load: the truck falls flat while towing, climbing or passing.
- Sputtering or hesitation: the engine stumbles when you press the throttle.
- Rough idle or stalling: the idle shakes or the engine dies.
- Check engine light: often with P0087, a low fuel rail pressure code.
- Metal in the fuel filter: fine, glittery flakes when you inspect the filter.
The 6.7 Powerstroke has two fuel pumps. A low-pressure lift pump moves fuel from the tank. The high-pressure Bosch CP4.2 pump then builds the pressure the injectors need. A problem with either pump can cause most of the symptoms above, so the signs overlap.
Early diagnosis matters. A failing CP4.2 can shed metal that travels through the rest of the fuel system. A cheap filter or lift pump problem left alone can turn into a much bigger repair.
Can a Bad Fuel Pump Cause a 6.7 Powerstroke to Crank but Not Start?
Yes. The engine needs enough rail pressure to fire the injectors. If the lift pump can’t feed the CP4.2, or the CP4.2 can’t build pressure, the engine may crank without starting. Check the filters and lift pump first, since they are the easier fixes.
Which Fuel Pump Is Failing: the CP4.2 or the Lift Pump?
The fastest way to tell them apart is the fuel filter. Low pressure with a clean filter points upstream. Metal in the filter points to the CP4.2.
| Pump | Location | Job | Typical symptoms | Typical codes | Cost risk |
|---|---|---|---|---|---|
| Lift pump (low pressure) | Fuel conditioning module on the frame rail | Pulls fuel from the tank and feeds the CP4.2 through the filters | Long cranking, power loss under load, sputtering, stalling | P0087 | Lower. Usually limited to the pump, filters or supply side. |
| CP4.2 (high pressure) | On the engine | Builds injection pressure for the fuel rails | Crank-no-start, sudden power loss, stalling, metal in the filter | P0087 | High. Metal can contaminate the injectors, rails and lines. |
What Are the Symptoms of a Bad Lift Pump on a 6.7 Powerstroke?
A weak lift pump starves the CP4.2 of fuel. You may notice long cranking, hesitation, and power loss that gets worse under heavy load or while towing. Low rail pressure codes can set, but the fuel filter stays free of metal.
The lift pump sits in the fuel conditioning module on the frame rail. Fuel passes through the filters before it reaches the CP4.2. That means clogged filters, air leaks or water in the fuel can mimic a bad lift pump.
How Do I Know if My 6.7 Powerstroke CP4 Pump Is Going Bad?
The clearest sign of a failing CP4.2 is metal flakes in the fuel filter. Other signs include low rail pressure while the supply side checks out, a sudden loss of power while driving, and crank-no-start. When the CP4.2 wears internally, metal debris can reach the injectors and fuel rails.
Decision Rule
- Low pressure + clean filter: check upstream first: filters, lift pump, air leaks and water.
- Glitter in the filter: suspect the CP4.2 and contamination downstream.
What Trouble Codes Point to a Failing 6.7 Fuel Pump?
The main code is P0087 (Fuel Rail/System Pressure Too Low). On the 6.7L, it means the engine computer sees actual fuel rail pressure falling short of commanded pressure.
P0087 does not prove the CP4.2 failed. Other causes include:
- Restricted or clogged fuel filters
- A weak low-pressure (lift) pump
- Air in the fuel supply
- Faults in the pressure-control parts
- Damaged wiring
How Do You Read Rail Pressure on a 6.7?
Use a scan tool that shows live data. Compare commanded rail pressure with actual rail pressure at idle and under load. If actual pressure keeps falling behind, the system can’t supply enough fuel. Then work through the supply side before you blame the CP4.2.
What Does Metal in the Fuel Filter Mean on a 6.7 Powerstroke?
Metal in the fuel filter usually means the CP4.2 is wearing internally. It also means debris has likely moved downstream into the rails, lines and injectors.
Owners call this the “glitter test.” Remove the filter, then cut it open or inspect the media and the housing. Look for fine metallic flakes that shine under a light. A clean filter does not rule out every problem, but glitter is a strong warning sign.
Warning: Don’t replace only the pump. If metal stays in the injectors, rails and lines, it can damage a new pump. A proper repair addresses the whole contaminated system.
Why Do 6.7 Powerstroke CP4.2 Pumps Fail?
The cause is disputed. Here are the main explanations on record:
- Fuel lubricity (owner claim): plaintiffs allege US diesel does not lubricate the CP4 well enough. They say this causes internal wear that sends metal through the fuel system. Ford disputes the defect claim.
- Aged biodiesel deposits (Ford recall): Ford’s recall filing says deposits can form on internal pump parts on some 2020-2022 trucks.
- Maintenance and contamination (Ford’s argument): Ford argues some owners did not replace dirty fuel filters or put DEF or gasoline in the fuel.
For context, Diesel World reports that CP4.2 failure is less common on the 6.7L Power Stroke than on the LML Duramax. For detailed causes and fixes, see our guide on a 6.7 Powerstroke starving for fuel.
What Years of 6.7 Powerstroke Have CP4 Pump Problems?
The class action covers 2011-and-newer 6.7L trucks with the Bosch CP4 pump. The recall targets 2020-2022 trucks. Ford used the recalled Bosch CP4 RP7 pump during the 2020 and 2021 model years, then switched production to an updated RP8 unit.
Is My Truck Covered by the 6.7 Fuel Pump Recall?
Your truck may be covered if it has the 6.7L diesel and is one of these models. NHTSA recall 24V-957 (Ford recall 24S78) covers certain 2020-2022 F-250, F-350, F-450, F-550 and F-600 Super Duty trucks and 2021-2022 F-650 and F-750 trucks. The recall covers about 295,000 US Super Duty trucks.
What Is the Risk?
Ford’s filing says aged biodiesel deposits can form on internal high-pressure pump parts. That can lead to pump failure and loss of drive power while you are driving.
What Is the Fix?
The remedy is a powertrain control module (PCM) software update, which Ford launched in January 2025. Refunds for earlier repairs are limited. They apply only if certain trouble codes were stored before the high-pressure pump repair and low-pressure fuel system flushing.
How to Check Your Truck
- Find your 17-character VIN on the dashboard, door jamb or registration.
- Enter it at nhtsa.gov/recalls.
- If the recall is open, call a Ford dealer to schedule the update.
- If you already paid for a pump repair, ask the dealer whether your records qualify for a refund.
What Is the Status of the CP4 Class Action Lawsuit?
On September 30, 2026, a Michigan federal judge certified classes of owners in California, Louisiana, Ohio, Pennsylvania and South Carolina. The case involves 2011-and-newer 6.7L Power Stroke trucks with the Bosch CP4 pump.
Certification lets the case move forward as a group. It does not decide whether Ford is at fault. CP4 lawsuits over 6.7L trucks have been filed since at least 2018.
Keep every repair order, receipt, filter change record and fuel receipt. Records help with recall refunds and any future legal claim.
Can You Keep Driving With a Failing 6.7 Fuel Pump?
It depends on the warning sign. Use these rules:
- Metal in the filter: stop driving. Tow the truck. Running it can push more debris through the system.
- Sudden loss of power: stop driving and tow. The next failure could happen in traffic or while towing.
- Pressure code with a clean filter: limit driving and check the filters and lift pump first.
The biggest risk is losing drive power while moving. That is dangerous on the highway, in traffic, or with a heavy trailer behind you.
Quick-Check Steps
- Scan the codes. Note P0087 and any other stored codes. Save them for recall or warranty records.
- Compare rail pressure. Watch commanded vs. actual rail pressure in live data at idle and under load.
- Replace or inspect both filters. The 6.7 uses two fuel filters. A clogged filter can cause low pressure on its own.
- Check for water and air. Drain the water separator and look for loose fittings or leaks on the supply side.
- Inspect the filter for metal. If you find glitter, stop driving and have the whole fuel system inspected.
If the filters are clean and pressure still lags, the problem may be the lift pump, a pressure-control part or wiring. A diesel shop can test each one before you commit to an expensive CP4.2 repair.
Frequently Asked Questions
How many fuel pumps does a 6.7 Powerstroke have?
A 6.7 Powerstroke has two fuel pumps. A low-pressure lift pump in the fuel conditioning module on the frame rail pulls fuel from the tank and sends it through the filters. The high-pressure Bosch CP4.2 pump on the engine then builds injection pressure for the fuel rails. A problem with either pump can cause similar symptoms.
Does a P0087 code mean the CP4.2 pump has failed?
No. P0087 means actual fuel rail pressure is lower than commanded pressure. It does not prove the CP4.2 failed. Clogged fuel filters, a weak lift pump, air in the fuel supply, pressure-control faults or damaged wiring can also set it. Check the supply side before you blame the high-pressure pump.
Can I replace just the CP4.2 pump after it fails?
Not if the pump shed metal. When a CP4.2 wears internally, debris can travel into the fuel rails, lines and injectors. If that metal stays in the system, it can damage a new pump. A proper repair addresses the whole contaminated fuel system, not only the high-pressure pump.
How many fuel filters does a 6.7 Powerstroke have?
The 6.7 Powerstroke uses two fuel filters. Fuel passes through them before it reaches the CP4.2 pump. A clogged filter can cause low rail pressure on its own and mimic a bad lift pump. Replacing or inspecting both filters is one of the first checks when a low-pressure code appears.
Can water or air in the fuel mimic a bad fuel pump on a 6.7 Powerstroke?
Yes. Water in the fuel, air leaks on the supply side and clogged filters can all starve the CP4.2 of fuel and look like a bad lift pump. Drain the water separator, check supply-side fittings for leaks and inspect both filters before you replace either pump.
