Quick answer: P2002 on a 6.7 Powerstroke means Diesel Particulate Filter Efficiency Below Threshold, Bank 1. Ford bulletins for certain 6.7L trucks tie it to a cracked DPF, and the published repair is DPF replacement. Check the pressure sensor, hoses, wiring, and exhaust leaks first. A regen will not repair a crack.
What does P2002 mean on a 6.7 Powerstroke?
P2002 is the OBD-II code for Diesel Particulate Filter Efficiency Below Threshold, Bank 1. In plain English, the powertrain control module (PCM) has judged that the diesel particulate filter (DPF) is not trapping soot as well as it should.
This is different from a filter that is simply full of soot. Ford bulletins for the 6.7L link stored P2002 to a cracked DPF, and the published repair is to replace the filter.
Which 6.7 Powerstroke trucks have a Ford bulletin for P2002?
Yes, Ford has technical service bulletins (TSBs) for P2002 on some 6.7L trucks. Two are confirmed in the bulletin summaries below.
| Bulletin | 6.7L trucks covered | Stated cause | Stated repair |
|---|---|---|---|
| TSB 20-2272 (August 19, 2020) | 2017-2020 Super Duty built on or after May 13, 2017 | Possible crack in the DPF substrate | Replace the DPF |
| TSB 22-2081 (March 8, 2022) | Some 2016-2017 F-650/F-750 | Cracked DPF and PCM software | Replace the DPF and reprogram the PCM |
TSB 20-2272 also lists 2015-2019 Transit 3.2L and 2018-2020 F-150 3.0L vehicles, but those are not 6.7L engines.
If your truck falls outside these ranges, no bulletin was confirmed for it here. That does not make it immune to a cracked filter or a P2002 code.
Before you buy parts, give a Ford dealer your VIN and ask about open bulletins and warranty status. Coverage depends on the individual truck, so get the answer in writing if you can.
What causes P2002 on a 6.7 Powerstroke?
The cause Ford documents is a crack in the DPF substrate, the honeycomb core that traps soot. Ford also names PCM software as a factor, but only in the F-650/F-750 bulletin.
Causes Ford documents
- Cracked DPF substrate: named in TSB 20-2272 and TSB 22-2081.
- PCM software: named in TSB 22-2081 for some 2016-2017 F-650/F-750 trucks.
Other faults to rule out first
The items below are diagnostic checks. They are not Ford-confirmed causes of P2002, but each can distort the exhaust data or hide the real problem.
- False DPF pressure readings
- Damaged, loose, or melted sensor hoses
- Damaged wiring or a corroded sensor connector
- Exhaust leaks near the DPF or its pressure ports
Can a bad DPF pressure sensor cause P2002?
Ford’s P2002 bulletins summarized here do not name the sensor as a cause. It is still worth checking because bad pressure data can mislead a diagnosis, and a sensor is a much smaller repair than a filter.
What symptoms come with P2002?
The documented sign is a check engine light, or malfunction indicator lamp (MIL), with P2002 stored in the PCM. A truck may show little else.
- Soot at the tailpipe: This is a clue that the filter may be damaged, but it is not proof on its own.
- Exhaust Filter or Drive to Clean messages: These relate to filter loading and regeneration. A full filter is a different condition from a low-efficiency code.
- Exhaust Overloaded, Drive to Clean: This message means the DPF is fully loaded or the truck has gone too many miles since its last regen.
Warning: If you ignore the Exhaust Overloaded, Drive to Clean message, the engine enters Limp Home mode with greatly reduced power.
How do you diagnose P2002 step by step?
Start with the data and the cheap checks. Do not clear the code until you have saved everything the PCM stored.
- Scan and save. Record all codes and freeze frame data.
- Note companion codes. Diagnose any sensor, wiring, or exhaust codes that appear with P2002.
- Check bulletins by VIN. Ask a Ford dealer which bulletins apply and whether the truck has warranty coverage.
- Inspect the DPF differential pressure sensor. With the exhaust cool, check the sensor, hoses, and connector for damage, looseness, or corrosion.
- Look for exhaust leaks. Soot trails at joints and clamps are a good place to start.
- Inspect the tailpipe. Note any soot, but weigh it along with your other findings.
- Compare live DPF pressure data. Use a capable scan tool and Ford workshop specs only. Generic values from forums can send you the wrong way.
For an example of how Ford checks this sensor, see TSB 17-0023. It has technicians read the DPF_INP_V PID with the key on and engine off. That bulletin applies to P244A on 2017 Super Duty 6.7L trucks, not P2002, so do not use it as a P2002 repair procedure.

How do you know if a 6.7 Powerstroke DPF is cracked?
There is no simple driveway test confirmed by these bulletins. A crack becomes more likely when the truck is in a bulletin range, the sensor inputs check out, and P2002 returns. Tailpipe soot adds weight to that conclusion. A Ford dealer can follow the current bulletin procedure to confirm it.
The decision rule
- Check further if you find bad data, damaged hoses or wiring, an exhaust leak, or companion codes.
- Try a regen only if the truck also shows a filter-loading message.
- Plan on DPF replacement if the inputs check out and P2002 returns on a bulletin-covered truck. Treat the DPF as the likely failed part.
Will a regeneration fix P2002?
A regen should not be expected to fix P2002. Ford’s bulletin summaries list DPF replacement for this code, not regeneration. A regen burns soot out of the filter, but it cannot repair a cracked substrate.
A regen still makes sense when the truck also shows a filter-loading message. In that case, you are dealing with the loading problem, which may exist alongside the P2002 fault.
Driving regen basics
RV.com reports that driving regeneration works best above 30 mph, ideally at 55 to 65 mph, for 15 to 30 minutes. Follow any message on your dash and drive only where that speed is safe and legal.
Operator commanded regeneration basics
- Citing Ford’s 2016 6.7L Super Duty Diesel Supplement, RV.com says it is started in Park with a warmed-up engine, through the Info button and display prompts.
- Pressing the brake or accelerator, or shutting off the engine, cancels it.
- The 2017 F-250 owner’s manual says it cannot be used until the DPF load reaches 100%.
- That manual also says a message requesting permission to start filter cleaning appears when the filter is near or at saturation.
Procedures and allowed conditions differ by model year, so follow the manual for your truck.
Safety warning: During active regeneration, the 6.7L Super Duty raises exhaust temperature to roughly 950 to 1,050°F. Park away from dry grass, fuel, and anything else flammable. Keep people and pets clear of the tailpipe.
How do you fix P2002 on a 6.7 Powerstroke?
Match the repair to what you found. Do not replace the DPF until the inputs have been checked, unless a dealer has confirmed the failure.
| Finding | Likely action | DIY or shop |
|---|---|---|
| Bad sensor, hose, or wiring | Repair the fault, clear the code, and verify it stays gone | DIY if you have a capable scan tool and Ford specs |
| Confirmed cracked DPF | Replace the DPF | Shop recommended; check bulletin and warranty status first |
| F-650/F-750 covered by TSB 22-2081 | Replace the DPF and reprogram the PCM | Dealer, because reprogramming needs dealer-level tools |
| P2002 returns after inputs check out on a covered truck | Treat the DPF as the likely failed part | Dealer or qualified diesel shop |
Can a cracked DPF be cleaned or repaired?
No. Cleaning removes trapped material, but it does not repair a cracked substrate. Ford’s published fix for this condition is replacement.
Confirm the part number first
TSB 20-2272 superseded TSB 20-2087 and added a new part and procedure for the same condition. An older part listing may be out of date, so confirm the current part number by VIN before you order.
Can you drive with P2002, and is a DPF delete legal?
Can you drive an F-250 with a P2002 code?
A truck with P2002 may still run, but the filter may not be controlling soot. Limit unnecessary trips and diagnose it soon. If you notice reduced power or a red warning, limit driving and get service.
Is a DPF delete legal?
A DPF delete is not a repair, and federal law restricts it. Under 42 U.S.C. 7522(a)(3)(A), no person may knowingly remove or render inoperative an emission control device or element of design after sale and delivery to the ultimate purchaser.
Section 7522(a)(3)(B) also restricts parts. It prohibits making, selling, offering to sell, or installing a part when a principal effect is to bypass, defeat, or render inoperative an emission control device, and the person knows or should know it is being offered or installed for that use.
The lawful path is to find the fault and repair it. Start with the inputs, check your VIN for bulletins, and replace the DPF if the evidence points there.
Frequently Asked Questions About P2002 on the 6.7 Powerstroke
Is P2002 the same as a clogged DPF on a 6.7 Powerstroke?
No. P2002 means the PCM has judged that the DPF is not trapping soot as well as it should. A clogged filter is simply loaded with soot and is tied to Exhaust Filter or Drive to Clean messages. Both problems can exist together, so a truck with P2002 may also need a regen.
Should I clear a P2002 code before diagnosing it?
No. Record all stored codes and freeze frame data before you clear anything. Then diagnose any companion sensor, wiring, or exhaust codes and check the DPF pressure sensor inputs. If you find and repair a bad sensor, hose, or wiring fault, clear the code and verify that it stays gone.
Does soot at the tailpipe prove a 6.7 Powerstroke DPF is cracked?
No. Soot at the tailpipe is a clue that the DPF may be damaged, but it is not proof on its own. Weigh it with your other findings, including sensor and hose checks, exhaust leaks, and bulletin coverage. A Ford dealer can follow the current bulletin procedure to confirm a crack.
Should I replace the DPF as soon as P2002 appears?
No. Check the DPF pressure sensor, hoses, wiring, and exhaust leaks first, unless a dealer has already confirmed the failure. Plan on replacement if those inputs check out and P2002 returns on a bulletin-covered truck. Before buying parts, ask a Ford dealer to check your VIN for open bulletins and warranty status.
Does an F-650 or F-750 with P2002 need more than a new DPF?
Yes, if TSB 22-2081 covers the truck. That bulletin applies to some 2016-2017 F-650/F-750 models and lists two repairs: replace the DPF and reprogram the PCM. Reprogramming needs dealer-level tools, so a Ford dealer is the right place for this job. Confirm coverage with your VIN first.
How do I find the right replacement DPF part number for P2002?
Confirm the current part number by VIN before you order. TSB 20-2272 superseded TSB 20-2087 and added a new part and procedure for the same condition, so an older part listing may be out of date. A Ford dealer can also tell you whether bulletin or warranty coverage applies.

