7.3 Powerstroke Camshaft Position Sensor (CPS) Symptoms: Stalling, No-Start, Codes and the Ford Recall

Quick answer: The most common 7.3 Powerstroke CPS symptoms are sudden stalling while driving, crank-no-start, hard starting and a rough idle. The problem may come and go before it fails for good. A bad sensor may or may not set code P0340 or P0344. Many 1997-2003 trucks are covered by Ford recall 07S57, so check your VIN first.

What are the symptoms of a bad CPS on a 7.3 Powerstroke?

A failing camshaft position sensor (CPS) usually shows up as a stall or a no-start. The engine may run fine one minute and shut off the next. According to The Diesel Store, a failing 7.3L cam sensor can cause these problems:

  • Sudden stalling while driving. The engine shuts off as if the key was turned off.
  • Crank-no-start. The starter spins the engine, but it never fires.
  • Hard starting. The engine takes much longer than normal to fire.
  • Rough or choppy idle. The engine stumbles or surges at idle.
  • Random shutdowns that come and go. The truck may restart after sitting, then stall again later.

Will a bad CPS cause a no-start on a 7.3 Powerstroke?

Yes. A failing CPS can cause a no-start with no warning. Many owners first notice it when the engine cranks but the tachometer needle does not move.

Does a bad camshaft position sensor always throw a code on a 7.3?

No. A failed CPS may or may not set a trouble code. A clean scan does not mean the sensor is good.

Definition: The CPS, also called the CMP (camshaft position) sensor, is a Hall-effect sensor. It sends a digital square-wave signal to the PCM, the truck’s engine computer.

What does the camshaft position sensor do on a 7.3L?

The CPS tells the PCM where the camshaft is and how fast it is turning. The PCM uses that signal to time the injectors and to know engine speed. It is also the signal that drives the tachometer.

The sensor uses three circuits: a 5-volt reference, a signal wire and a ground, as Riffraff Diesel explains. If the signal drops out, the PCM no longer knows when to fire the injectors. That is why a bad CPS can shut the engine off instantly instead of just making it run poorly.

Which trouble codes point to a bad 7.3 CPS?

Two codes point directly at the cam sensor circuit:

CodeMeaningWhat it usually suggests
P0340Camshaft position sensor circuitThe PCM sees a fault in the CPS circuit: the sensor, wiring or connector
P0344Camshaft position sensor intermittent signalThe signal drops in and out, which matches stalls that come and go

Keep these points in mind when you scan:

  • No code does not clear the sensor. A CPS can fail without setting P0340 or P0344.
  • Use a scan tool that reads Ford diesel codes. Some basic code readers miss diesel-specific data.
  • Check live data if your tool offers it. Watch engine RPM while cranking. If RPM reads zero while the engine is clearly turning, the PCM is not getting a cam signal.

Is my 7.3 Powerstroke covered by the Ford CPS recall?

Maybe. Ford recall 07S57 (NHTSA campaign 07V553000) covers 1997-2003 Ford F-Super Duty, E-Series and Excursion vehicles with the 7.3L diesel. It was reported on December 5, 2007, and included about 1.18 million vehicles.

How do I tell if I have the old or new sensor?

Look at the color. Ford’s dealer instructions identify the sensors this way:

Sensor lookStatus
Gray sensor with a silver bracketNot affected (updated sensor)
Black sensor with a gold bracketAffected, must be replaced

If you see a black sensor with a gold bracket, your truck likely still has the original part. Even a gray sensor can fail, so it does not rule out the CPS completely.

Comparison of the old black 7.3 cam sensor with gold bracket and the updated gray sensor with silver bracket.Old sensorUpdated sensorBlack sensorGold bracketReplace itGray sensorSilver bracketNot affected
Black sensor with gold bracket is affected by the recall; gray with silver is the updated part.

How do I check my VIN for open recalls?

  1. Find your 17-character VIN. It is on the driver’s side of the dashboard near the windshield, on the door jamb sticker and on your registration.
  2. Go to nhtsa.gov/recalls or Ford’s recall lookup page.
  3. Enter the VIN and look for recall 07S57 / 07V553000.
  4. If it shows as open, call a Ford dealer and book the free repair.

How can I tell a bad CPS from other 7.3 problems?

Several 7.3 parts can cause stalling or no-start. Use this table to decide where to look first:

What you seeMost likely suspect
Sudden stall or crank-no-start, with P0340 or P0344Camshaft position sensor (CPS)
Sudden stall or no-start, tach dead while cranking, no codesCPS or its wiring (check first)
Codes or symptoms tied to injection control oil pressureICP sensor or high-pressure oil pump (HPOP)
Injector-related codes or a misfire on one or more cylindersInjector driver module (IDM) or the under-valve-cover harness
No communication with the scan tool, or many unrelated codesPCM or its power and ground supply

Quick tach check: Watch the tachometer while someone cranks the engine. If the needle stays dead, that is a common clue that the PCM is not getting a cam signal. Treat it as a clue, not proof. Wiring, connector or PCM problems can cause the same result.

If the tach moves while cranking and you have no CMP codes, look at the other systems. See our guides on [INTERNAL LINK: 7.3 ICP sensor symptoms], [INTERNAL LINK: 7.3 IDM symptoms], [INTERNAL LINK: 7.3 PCM problems], [INTERNAL LINK: 7.3 HPOP failure] and [INTERNAL LINK: 7.3 under-valve-cover harness].

Where is the camshaft position sensor on a 7.3 Powerstroke?

The 7.3 CPS is on the front of the engine, just above the crankshaft damper. When you face the engine, it sits at about the 11 o’clock position, as DieselHub shows. A single 10 mm bolt holds it in place.

Before you buy a new sensor, inspect the connector and pigtail. Look for:

  • Oil inside the connector or soaking the wires
  • Green or white corrosion on the pins
  • Cracked, rubbed or melted insulation
  • A loose plug or a broken locking tab

A damaged connector can cause the same stalls as a bad sensor. Fixing it may solve the problem for less money.

How do I replace a 7.3 CPS? (Step by step)

Replacing the CPS is a simple job with basic hand tools. Check the recall first, since an open recall means the dealer does it for free.

  1. Disconnect the batteries. Remove the negative cables from both batteries.
  2. Unplug the connector. Release the locking tab and pull the plug straight off. Do not pull on the wires.
  3. Remove the 10 mm bolt. Set it aside where it cannot fall into the engine bay.
  4. Pull the sensor out. Twist it gently as you pull. If it is stuck, work it back and forth instead of prying hard.
  5. Check the O-ring. Make sure the old O-ring came out with the sensor and is not left in the bore. The new sensor should have a fresh O-ring. A light coat of clean engine oil helps it slide in.
  6. Install the new sensor. Push it fully into the bore and refit the 10 mm bolt. Snug it down without over-tightening.
  7. Plug in the connector. Push until the lock clicks.
  8. Reconnect the batteries, clear codes and test-drive. Watch the tach while cranking and drive long enough to confirm the stalling is gone.

Buy the right part. Replacement CMP sensors are sold for specific model-year ranges. 1994-1996 trucks use a different part from 1997-2003 trucks, and some sensors come with a pigtail. Match the part to your year before you order.

Can you drive a 7.3 Powerstroke with a bad CPS?

No. A bad CPS can stall the engine with no warning. When the engine dies, you lose power steering assist and power brake assist. The truck becomes much harder to steer and stop, which is risky at highway speed or in traffic.

Follow this order:

  1. Check your VIN for open recall 07S57 / 07V553000.
  2. If the recall is open, have the dealer replace the sensor for free.
  3. If the recall is done, check the sensor color, the connector and the tach while cranking.
  4. Replace the sensor if it fails those checks, then test-drive before trusting the truck again.

7.3 Powerstroke Cam Sensor FAQ

Does a bad cam sensor stop the tachometer on a 7.3 Powerstroke?

Yes, it often does. The cam sensor signal drives the tachometer on a 7.3L. If the needle stays dead while the engine cranks, the PCM is likely not getting a cam signal. Treat this as a clue, not proof. Wiring, connector or PCM problems can cause the same result.

Can a bad CPS connector cause the same symptoms as a bad sensor?

Yes. A damaged connector or pigtail can cause the same stalls as a failed sensor. Check for oil in the connector, green or white corrosion on the pins, and cracked or melted insulation. Also look for a loose plug or a broken locking tab. Fixing the connector may solve the problem for less money.

Can the updated gray cam sensor on a 7.3 still fail?

Yes. The gray sensor with a silver bracket is the updated part, and it is not covered by recall 07S57. It can still fail, though. A gray sensor does not fully rule out the CPS. If you still have stalling or a dead tach while cranking, inspect the sensor, its connector and its wiring.

Do 1994-1996 and 1997-2003 7.3 trucks use the same cam sensor?

No. Replacement CMP sensors are sold for specific model-year ranges, and 1994-1996 trucks use a different part from 1997-2003 trucks. Some sensors also come with a pigtail. Match the part to your truck’s year before you order to avoid buying the wrong sensor.

What tools do you need to replace a 7.3 Powerstroke cam sensor?

You need only basic hand tools. One 10 mm bolt holds the sensor at the front of the engine, above the crankshaft damper. Disconnect both batteries first. Then unplug the connector, remove the bolt and pull the sensor out. A light coat of clean engine oil helps the new O-ring slide in.